CNC Production Center , (ATC) Automatic Tool Change

Caractéristiques:

• Unité mécanique avec un contrôleur de (X,Y,Z) intégré.

• La vitesse dépend de la résolution du pas (Vitesse max 5metres/min)

• Résolution du pas ajustable 0,0254mm.

• Interface RS232

• Les paramètres de la machine contrôlable avec le software.

• Logiciel pour le perçage et le routage.

• La sélection des outils de perçage automatique.

Alimentation : 230V 50Hz.

Surface de travail : 324 mm X 495 mm.

Poids : 30 Kg.

CNC Production Center , (MTC) Manual Tool Change

Caractéristiques:

• Unité mécanique avec un contrôleur de (X,Y,Z) intégré.

• La vitesse dépend de la résolution du pas (2,3m/mn ou 1,5m/min).

• Résolution du pas ajustable 0,01 ou 0,005mm.

• Précision ±0,01mm

• Interface RS232

• Les paramètres de la machine contrôlable avec le software.

• Logiciel pour le perçage et le routage.

• La sélection des outils de perçage manuelle.

Alimentation : 230V 50Hz.

Dimensions : 500 X 500 X 500 mm.

Surface de travail : 210 mm X 340 mm.

Poids : 15 Kg.

SPLASH CENTER: SPRAY ETCHING MACHINE

A professional unit that integrates all important steps of PCB wet processing.

Spray etching compartment:

•Professional spray etching technology

•100 µm line definition

•Etching speed with standard Fe-III-Cl: 35 µm Cu in 90s

•Max. board size 210 x 300 mm

•Magnetic driven spray pump

•Built-in 1000 W heater

•Thermostat controlled

•Overheat protection

•Security lid switch

•Digital timer with count-down, auto-reset and beeper

•Also suitable for spray developing

•Special shadow-free PCB holder (titanium)

•Drop-off position for holder

Four Treatment tanks (from left to right side):

•Static pre rinse

•Static plus fresh water spray rinse (including magn. valve and foot-switch)

•Tank with filter basket and bath movement by pump, for resist stripping or developing

•Spare tank, i.e. for chemical security tray.

Features

•All bathes covered by lids

•All bathes can be emptied by front integrated cog-valves

•PCBs may pass all wet processing steps in one PCB holder

•Inclusive anti-pollution security tray

660TC: Station de Soudage Standard

• Alimentation : 110/120 230Vac.

• Température : 65° à 450°.

• Indicateur d’énergie (ON/OFF) : LED verte.

• Indicateur d’énergie sur le fer a souder : des LED rouges.

• Capteur : Thermocouple.

690SD: Station de Soudage Standard.

• Alimentation : 110/120 230Vac.

• 4 afficheurs LED rouges.

• Température : 65° à 450°.

• Indicateur d’énergie (ON/OFF) : LED verte.

• Indicateur d’énergie sur le fer a souder : des LED rouges.

• Capteur : Thermocouple.

FTX Machine de Perçage Haute Précision

FTX Optical Drilling Machines:

  The FTX Optical Drilling Machine has been designed to provide all the advantages of accurate optical drilling at a relatively low cost, yet without compromising precision or ease of use. The machine is electro-pneumatically controlled, with a large screen optical unit, high intensity illumination and clear definition to minimise operator fatigue. The projector unit gives a balanced magnification of 7:1, while work piece illumination is provided by two high-inten-sity lamps, which can be easily adjusted for

optimum light concentration.

Air is introduced to the machine by means of a separate three-positioned isolating switch. Depression of the two-position foot switch clamps the circuit board, allowing the operator to check the accuracy of alignment of the board to the screen centre. Further depression of the foot switch initiates the drilling cycle and on completion, releases the clamp for the next operation.

The automatic drilling spindle has an adjustable feed rate for all sizes of drilled holes. A retractable bellows unit surrounds the chuck and is connected to an outlet pipe at the rear of the machine for connection to a swarf extraction unit (not included). The large capacity key-type drill chuck is easily

accessible for drill changing by pivoting the counter balance projector head back-wards.

 The matt finish steel base plate incorporates a drill bush adapter which accepts most standard drill bushes.

The unit is mounted on a rigid cantilever-type stand with a large laminated work top which provides ample work space. A drawer is provided for convenient storage of drill bits, tools and accessories.

VarioDrill, Machine de Perçage a Grande Vitesse

Features:

• Throat depth: 115 mm

• DC Motor, 100 Watts / 230 Volt

• Infinitely adjustable 10000...30.000 RPM

• Power output 90 Watts

• Chuck: 1/8" (3,2mm)

• Drill size 0,6 to 3,2 mm

• Adjustable stroke speed

• Adjustable m/c tilting between 0-30

• Lighting unit built-in 6 V - 1,5 W

• Complete system with integrated dust extraction

• Including external vacuum cleaner

• Including foot switch for easy operating, that way

• Booth hands are free to positioning the PCB

FX-5R, Machine de Perçage et de Routage

FX-5R PCB Routing Machine:

A modified version of the FX-5 Drilling Machine also suitable for routing PCBs.

The machine has a fence and depth stop

and is fitted with special bearings, allowing it to withstand heavy side loadings.

The router is ideal for making cut-outs in edge connectors, shaping complicated contours, removing unwanted tracks, or chamfering rough edges of circuit boards.

DM-403 Machine de Perçage a Grande Vitesse

DM-420 Machine de Perçage

Unités Ultra Violet

DM9000    8"                           DM9001    12"

DM 525   25"

ES420 Corner Rounder

Table Traçante LY16100II

LaboratoireComplet pour PCB